Thin Air Press Bag 36 x 52" Expand

Thin Air Press Bag 36 x 52"

New

£ 86.90

tax incl.

The Thin Air Press 36 x 52' (95.5 cm x 132 cm) is an inexpensive introduction to vacuum laminating and can be used for projects from laminating skateboard decks, to building furniture parts. The press can be re-used many times, and other sizes are available to suit your project. Easy to use, no power required. This is how you Bend it with Thin Air!

Get multiples of this size bag for production work, or as a replacement or addition to your other sizes.

Useful for schools and groups and garage builders who require multiple bags so that more than one project can be made during the same gluing session.

The Thin Air Press 36 x 52'' (95.5 cm x 132 cm):

36 x 52'' (95.5 cm x 132 cm) vinyl vacuum bag with a one-way valve positioned in the center or offset and seal attached

How to use this product:

To be used with the breather netting and pump you already have.

Insert your glued veneers (and mold) into the heavy-duty vinyl vacuum bag, position the breather netting under the valve, seal the bag, connect the manual pump and in less than a minute, extract the air out. 

Watch as it generates enough pressure to press 1/16 veneer (or thinner) over a mold. Or laminate a fancy veneer to a flat surface. It can also be used without an internal mold or platen, see the tutorials in the how-to section.


Before you glue your veneers together, a dry run is highly recommended!


FAQs:

Q: Is this reusable, and for how many times?
A: The kits are designed to be used many many times. With a little care and maintenance, the TAP Kits will last for years.


Q: Will the glue stick to the bag?
 

A: PVA glue and epoxy will not stick to the bag. Any dried glue can be loosened with fingers and either shaken or blown out with a shop vac.


Q: How many boards can I press at once?
 

A: One board at a time. You are limited by how fast your glue dries. Once you start spreading water-based glue on the veneer sheets, you have about 7 minutes to get them pressed before the glue dries. Dry glue will not bond together.


Q: If the TAP Bag gets a hole in it, can I fix it?
 

A: Clear 2 packing tape seals up any suspected punctures. Use a length of the butyl tape to fix any side seam gaps or splits.


Q: Do the valves leak?
 

A: While many people assume air is leaking back through the valve, they are made of cast rubber and almost never leak. The most common problem with slow leakage is the open-end seal tape. If the seal is not properly closed up (check both sides) you will lose vacuum. If the top cap of the valve is not compromised with dust and debris, the valve will not leak.


Q: Do you refund my veneer if I screw up the pressing?
 

A: If you are unsure about any part of the process, we are only a phone call or email away and are happy to give advice and support. However, we cannot refund for any failed pressings.


Q: Whats a Dry Run and why should I do that?
 

A: It means to press your project in the TAP bag, without putting any glue on the veneer sheets. Stack the dry sheets of veneer over the mold, seal them into the press with the breather netting in place, and pump the air out. Check for 10 minutes to make sure the TAP bag is not leaking. This will help you become familiar with the process before you commit glue to your veneer sheets.

No customer reviews for the moment.

Write a review

Thin Air Press Bag 36 x 52"

Thin Air Press Bag 36 x 52"

One way ValveChoose centre or offset placed valve
Width95.5 cm (36'')
Length132 cm (52'')
Thickness20 mil (0.5mm)
Breather nettingnot included
Thin Air Press Pumpnot included
Extra sealing tapenot included
StrengthAround* 14.22 psi (1kg/cm²)

Want to build your own skateboard in a workshop environment?

Join us at the FAR Academy, the UK's first and only skateboard building academy. School student and adult classes available.

More Info 

Accept

This site uses cookies to store your basket and preferences.